For this blog posting I am going to concentrate on the Herringbone Stitch. There are many variations of this stitch, depending on the slant of the stitch, the width and the height of the stitch, as well as the numbers of threads in the separation of each “v” of the stitch. Compensation must take into account all of these variations, there is not one way to do it for every variation of the stitch.
Let’s look at the Herringbone Stitch that is two threads high and two threads wide:
Herringbone Stitch - 2 wide x 2 high |
The red lines show the compensating stitches. Since this stitch follows the 45 degree diagonal of the square grid, the compensation is straight forward and no guessing is needed.
Here is a stitched sample:
Herringbone Stitch - 2 wide x 2 high |
Looking at the back of the canvas:
Herringbone Stitch - back of canvas |
There is not much thread on the back of the canvas to weave in ending threads. In fact the stitches on the back of the canvas are over one thread.
Let’s look at two difficulty issues that the Herringbone Stitch may cause:
- It is hard to end threads on the back of the canvas.
- The step back stitch (as in going from 2 to 3), the thread goes back one canvas thread and many times it can be pulled under the thread that is supposed to separate where the needle went into the canvas (at point 2) and where it is brought out of the canvas (at point 3.)
For Point 1:
The first piece of advice that I can give about weaving in ending threads is : get a sharp needle - a crewel needle or an embroidery sharp needle is better than a sewing needle, but that will work too. The embroidery sharp needle is the easiest to use because the eye of the needle is as large as a tapestry needle.
Let’s look at a stitched Herringbone Stitch sample:
Herringbone Stitch ending threads showing through to front of canvas |
The arrows are pointing to ending threads showing through to the front of the canvas. Let’s look at the back:
Red arrow - ending threads diagonally on the back of canvas
Blue arrow - ending threads horizontally on the back of the canvas
|
This is the back of the sample and you will notice that you do not see the ending threads on the left side of the stitching where the ending threads are woven into the stitches on the back (and I had to use a sharp needle because there is not much thread on the back of the canvas.) Notice that ending the threads horizontally means that the ending threads show through to the front. It is much better to end the threads on a diagonal on the back, meaning you have to weave through a top stitch, then a bottom stitch, then a top stitch, etc.
Other options for ending threads - weave them into stitches next to the Herringbone Stitches. This is an option, but unless I absolutely have to (like for darning stitches) I always try to end threads behind the stitches that the thread was used to stitch them. Why?
First, I don’t have to worry about thread shadows showing through stitches with lighter colored threads. Second, if I have to rip out stitches, I don’t want to disturb stitches in surrounding areas - this just makes it easier for me. If you’ve ever ripped out stitches and had all these ending threads in them from other areas you’ll know that this can really be a problem. Maintaining stitch tension on those stitches from surrounding areas is nigh impossible.
Now for Point 2:
Having threads slide under the intersection of the canvas thread is a pain. Let’s look at the canvas:
Canvas thread on top is vertical |
When the top thread is vertical, any stitch over one horizontal canvas thread (as in the Herringbone example above) may slip under that vertical canvas thread. This usually happens when the area you are stitching in has been disturbed (as in ripping out stitches and stitching over the area again.) Canvas has some starch in it and that makes the canvas threads “stitck” a bit to each other when you first stitch on the canvas. However, if you break this bond, then threads can easily slip around, as well as disforming the canvas threads with tight stitching tension.
This is a problem with a linen ground fabric also. People who work on linen have to take more care in their stitching tension than canvas stitchers. So watch your tension.
Try not to start a horizontal run of Herringbone Stitch that has an over one canvas thread stitch across the back of the canvas with a vertical stitch on the top.
Canvas thread on top is horizontal |
Now let’s look at a variation of the Herringbone Stitch that is not square.
Herringbone Stitch - 3 high x 4 wide
|
Herringbone Stitch - 4 wide x 3 high - Arrows pointing to compensated stitches
|
The compensated stitches are executed with white thread so that they stand out. I will look at the slant of these stitches to determine if they are correct. With this sample, I am happy with the slant - that is the only way to know if a compensated stitch will work - look at the slant of the stitch and compare it to a previous whole stitch.
No comments:
Post a Comment